Residential and commercial electrical servicesCall (754) 226-1874

Equipment

Meter Sockets and Service Equipment Explained

Between the utility wires and your electrical panel sits a chain of equipment: the service drop, mast, weatherhead, meter socket, disconnect and main breaker. Some of it belongs to the utility, some belongs to you, and knowing the difference tells you who to call when something looks wrong.

24 Hour Electrician Near Me technician carefully inspecting a residential breaker panel

The path power takes into a building

Electric power reaches a home in a sequence. Overhead service starts with wires from a utility pole, called the service drop, which attach to the building at a point on the house and enter a weatherhead, a curved cap at the top of a pipe called the mast. The wires run down through the mast to the meter socket, the box where the utility meter plugs in. From the meter, conductors run to the main disconnect and then to the distribution panel that feeds your circuits.

Underground service follows a similar path but comes up from the ground through a conduit, sometimes from a pad-mounted transformer or from a pole, and enters the meter socket from below. Many newer subdivisions and condominium complexes use underground service, while older neighborhoods often have overhead service. Multi-unit buildings may have a bank of meters in a central meter room or on an exterior wall, with each unit's feeder running to its own panel.

Understanding this chain helps because problems show up at different points. A lean in the mast, a damaged weatherhead, a cracked meter socket or a corroded connection can each create a different symptom. And because the equipment is divided between the utility and the owner, the right call depends on where the issue sits.

24 Hour Electrician Near Me electricians reviewing a commercial electrical panel

What the utility owns and what you own

The general pattern in Florida is that the utility owns the service drop wires and the meter itself, and the customer owns everything on the building side starting at the point of attachment, including the mast and weatherhead, the meter socket, the conduit, the main disconnect and the panel. The exact boundary can differ by utility and by service type, so the specific utility's rules decide in a given case.

This matters in practice. If the service drop wires have been pulled down by a tree, or a line is sagging, hanging or sparking out at the street, the utility handles it and you should keep away. If the mast is bent, the weatherhead is cracked, the meter socket is damaged or the main disconnect is failing, those are the owner's responsibility, and a qualified electrician makes the repair, usually coordinating with the utility for disconnect and reconnect.

In some situations the utility must be involved before the work begins. The utility may need to cut the service drop or pull the meter so the electrician can work safely. Pulling a meter without authorization is not permitted and is dangerous. The utility meter and service responsibilities guide explains the division in more detail and what to expect when a coordinated shutoff is needed.

The meter socket

The meter socket, also called a meter base or meter can, is a metal enclosure with jaws that hold the utility meter. It has terminals for the incoming service conductors and outgoing conductors to the panel. Sockets are sized by the amperage of the service, and they come in ring and ringless styles, with different arrangements for single meters and multi-meter banks.

Over time a socket can develop problems. Moisture and salt cause corrosion of the jaws and terminals, leading to heat, discoloration and intermittent power. Storms can crack the enclosure or pull the box away from the wall. Insects, lizards and wasps can build in or near the socket. An impact from a vehicle or a lawn tool can bend the box. Overheating of the jaws can melt the meter base, which sometimes shows as a brown or black stain or a melted meter housing.

Signs that the socket needs attention include a meter that looks loose, a cracked or missing cover, a burning smell, buzzing or crackling from the box, discoloration, water inside, or lights that flicker in a pattern that suggests a poor connection at the service. Do not touch the box, and do not try to push the meter back into place. See meter socket replacement for how the repair is handled and what coordination with the utility is involved.

The mast, weatherhead and service drip loop

On overhead service, the mast is a metal pipe, usually rigid conduit, that rises above the roofline or alongside the wall to support the service drop wires at a minimum height above the roof or ground. The weatherhead at the top keeps rain out of the pipe. A drip loop in the wires just before entry lets water run off the wire instead of following it into the pipe.

The mast carries mechanical stress. The wires pull on it, and wind, falling branches and storms add load. In hurricane-prone areas a mast can be bent, its guy support loosened or its roof flashing broken, which can leak water into the attic and the service equipment. Rust on a mast, cracks at the weatherhead and loose straps are all warning signs.

If a mast is leaning or the wires are pulled tight, keep clear and call. Repairs often require the utility to disconnect the service, and the electrician must reinstall the mast and equipment to local standards, usually with a permit and inspection. The service mast and weatherhead repair page explains this process. For properties that took a storm hit, the after hurricane electrical safety guide lists what to check before reconnecting power.

Main disconnect, main breaker and panel

Inside or beside the house, the service conductors reach a main disconnect. In many homes the disconnect is the main breaker in the panel, the large breaker at the top that shuts off everything in the house. In others, it is a separate box outside near the meter, which provides a place to cut power without entering the house. Local rules require a readily accessible disconnecting means, and some jurisdictions require the exterior disconnect on new work.

The main breaker protects the service conductors and the panel busbar. It is sized for the rating of the service, such as 100, 150 or 200 amps. It should never be treated as a convenient on and off switch, but knowing where it is and how to turn it off is basic household safety. In an emergency, such as flooding or a fire, shutting it off from a safe, dry location can help, but only if it is safe to reach.

Beyond the main disconnect is the distribution panel, covered on other pages of this site such as electrical panel repair. A technician evaluating the service looks at all of these components together, because the weakest link determines the usable capacity of the whole service.

Grounding electrode and bonding at the service

The service equipment is also where the grounding system connects. A grounding electrode conductor runs from the service neutral and grounding bus to one or more grounding electrodes: ground rods, a metal underground water pipe, concrete-encased steel in the foundation, or other approved electrodes. The metal parts of the service equipment are bonded together so any fault current has a low-resistance path back to the source and the breaker trips.

Many older homes have grounding that is missing, corroded, disconnected or inadequate by present standards. Replaced water pipes, switched from copper to plastic, can remove an electrode without anyone noticing. Rusted clamps and broken wires at ground rods are common in humid, salty areas.

If you see a wire from the meter or panel running to a ground rod, do not move or cut it. Grounding is a safety system, and the details are covered on the grounding and bonding explained page. If a surge or a storm has damaged the service, the grounding connections should be checked as part of the repair.

Common failures and what they look like

Failures of service equipment tend to show up as a handful of recognizable patterns. Partial power loss, where half the house is dark, can point to a lost leg at the service, a failing connection in the meter socket or a utility-side problem. Flickering and dimming across the home may come from a loose connection in the service path. A burning smell, a hot meter, or a melted meter base needs immediate attention.

Water intrusion is another frequent problem in Florida. A damaged weatherhead, a gap at a conduit entry, a missing knockout cover, or a cracked meter socket can let rain into the equipment. Moisture leads to corrosion, shorts and ground faults, and in a worst case it can energize metal parts. Water inside a panel is an emergency, and the water in electrical panel page explains what to do.

Physical damage is common after storms and from vehicles or landscaping equipment. A meter box hanging loose from a wall, a socket knocked askew, or a bent conduit is a hazard. See meter box damaged or hanging for guidance.

  • Half the house without power while the other half works.
  • Lights dimming or flickering in a way that follows no pattern.
  • Burning smell, crackling or buzzing from the meter or service box.
  • Discoloration, melting or soot around the meter jaws or cover.
  • Rust, water stains or moisture inside the socket or disconnect.
  • A loose, tilted or detached meter box or leaning mast.

Upgrades and replacements

Sometimes the service equipment is simply old and undersized. A home built decades ago may have a small service that cannot handle central air conditioning, an electric range, a pool, a water heater and an EV charger all at once. Upgrading means replacing the meter socket, mast, service conductors, disconnect and panel to a higher rating, with a permit, an inspection and utility coordination.

A larger service is not always necessary. A load calculation, which adds the demand of existing and planned equipment according to established rules, shows whether the present service is adequate. Sometimes load management devices, which limit simultaneous use of large appliances, are an alternative. The choosing electrical service size page discusses the decision, and main service upgrade covers the work.

During an upgrade, the technician typically also corrects grounding, replaces corroded components, labels the equipment and installs surge protection if desired. Scheduling must account for permit review, utility disconnect and reconnect, inspection and the time the home spends without power. Planning ahead around hurricane season is wise, since utility and inspection schedules get crowded after storms.

What owners should check and what to leave alone

An owner can do a simple visual walk-around. From the ground, look at the mast for lean or rust, at the weatherhead for cracks, at the conduit and meter box for loose straps or gaps, at the meter for a clear view of the glass and seal, and at the area around the equipment for vegetation, wasp nests, clutter or standing water. Keep the area clear for access by the utility and by electricians.

Leave the equipment itself alone. Do not open covers, break seals, remove the meter, reach into the box, or work near the service drop. Do not try to repair a leaning mast, tighten connections or cut wires. The service conductors in the meter socket are live and unfused on the line side, which means the main breaker cannot protect you from them.

If you see damage, hear buzzing, smell heat or notice water in the equipment, call right away. If wires are down or a line is sparking in the street, stay away and call 911 and the utility. When you call us, tell us what you see, where it is, and whether you still have power. Quotes are given by phone, complicated service work gets an on-site visit first, and the service call charge for that visit is explained before dispatch.

Questions people ask

Who is responsible for the meter socket, me or the utility?

In general, the utility owns the meter and the service drop wires, while the customer owns the meter socket, mast, weatherhead, conduit, disconnect and panel on the building side. The exact boundary can vary by utility and service type. If you are unsure, call and describe what you see. A qualified electrician coordinates with the utility when work requires disconnecting or reconnecting service.

Can I remove the meter myself to make repairs?

No. Meters are utility property and have seals, and the jaws behind the meter are live. Removing a meter without authorization is not permitted and exposes you to serious electrical hazard. If work requires the meter to be pulled, the electrician coordinates with the utility, and in some cases the utility personnel perform the removal and reinstall it after inspection.

My service mast is leaning after a storm. Is that urgent?

It can be. A leaning mast puts stress on the service drop wires and the connections, and it can pull the wires loose or allow water into the equipment. Keep people away from the area and do not touch it. Call so a technician can assess it, and expect that the utility may need to disconnect the service before repairs can be made.

Why is my meter box buzzing or warm?

A faint hum can be normal in some equipment, but a loud buzz, crackle, heat or burning smell can indicate a loose connection, corroded jaws or an overloaded service. Heat is how connections fail. Stay clear of the box, do not open it, and call promptly. If you see smoke, flames or melted plastic, call 911 first.

Do I need a permit to replace a meter socket?

In most places, yes. Replacing a socket affects the service equipment and the utility connection, so a permit, an inspection and utility coordination are typically required. The specific steps depend on the city or county and on the utility. A technician familiar with local practice can explain what applies and handle the coordination.

How do I know if my service is big enough?

Look at the main breaker rating, usually printed on the handle, and consider what you run: central air conditioning, an electric range, dryer, water heater, pool equipment and any EV charger. A load calculation provides a real answer. Signs of strain include frequent main breaker trips, dimming when large appliances start, and an old panel with no open spaces. Call and we can discuss it.

Talk to 24 Hour Electrician Near Me

If "Meter Sockets and Service Equipment Explained" sounds like your problem, call and describe what you see, hear or smell at the panel, the outlet or the fixture. We explain what the work involves, and some jobs need a visit before a quote.

Related pages

  • Meter Socket: Who does what when a meter socket is damaged: the owner, the electrician and the utility, how power is disconnected and restored, and how to plan the repair.
  • Service Mast Repair: Storm-bent masts and pulled weatherheads: what the electrician repairs, what the utility handles, safety around the line to the house, and how repairs proceed.
  • Meter Responsibilities: Where utility equipment ends and the property owner's equipment begins at the electric meter, and who repairs what when something is damaged.
  • Grounding and Bonding: What grounding electrodes, bonding jumpers and equipment grounds each do, why many older Florida homes lack them, and how a technician checks yours.
  • Service Upgrade: When a home outgrows its electrical capacity: replacing the service entrance, meter base and main disconnect, how the utility fits in, and what to expect.
  • Smart Panels: Circuit-level monitoring and load-shedding devices explained for homes with EV chargers, heat pump equipment and backup power, and how they fit a panel.

How a meter socket job unfolds from the first visit to the last

A job involving the meter socket rarely starts with tools. It starts with a conversation about why the socket needs attention: a cracked cover, a burned smell, rust at the base, a loose mounting, or a planned service upgrade. The technician looks at the socket from the outside first, noting corrosion, cable entry points, and how the enclosure is fastened to the wall. Because the utility controls the meter and the seals around it, the scope that gets explained before work begins also spells out which steps belong to the utility and which belong to the electrical contractor.

Once the scope is agreed, the sequence matters. Power to the building has to be removed upstream of the socket, and that step often depends on coordination with the utility rather than on a simple switch at the panel. The technician confirms the line side is de-energized with a tester before touching anything, because the conductors feeding the socket can stay live even when everything inside the house is switched off. Only then are the old socket and its connections removed, the conductors examined for heat damage, and the new enclosure set level and secured.

After the new socket is mounted and terminated, the work is not finished. Terminations are torqued, conductor insulation is checked for nicks, and the cable entry is sealed so Florida rain cannot track inside. Then the paperwork and utility steps take over, which can include an inspection and the utility reinstalling the meter. Owners should plan for a stretch without power and should ask the office to explain the sequence in advance. Call us to talk through your situation and confirm availability for your area. Small details noted at this stage tend to save a second trip later, so mention anything unusual even if it seems minor.

Talk through the electrical service you need.

Request service
Call (754) 226-1874