Residential and commercial electrical servicesCall (754) 226-1874

Services

Upgrading the Main Electrical Service

The main service is the doorway between the utility and your home's wiring. When it is too small, worn or damaged, nothing downstream can be fully fixed. This page explains what a service upgrade includes, how the utility and the electrician share the work, and what to plan for.

24 Hour Electrician Near Me technician carefully inspecting a residential breaker panel

What the main service is

The electrical service is everything between the utility's lines and your main panel. It includes the wires that arrive from the pole or underground, the weatherhead or underground connection, the service conductors, the meter socket, the main disconnect and the grounding connections. The panel then divides the incoming power into branch circuits.

Think of it as a pipe feeding the whole house. The size of the pipe is the service capacity, measured in amps. A home with a small service can only carry so much at once, no matter how many breakers sit in the panel. Add central air conditioning, an electric range, a dryer, a pool pump and a car charger, and the household may demand more than the service was designed to deliver.

Services also age. Meter sockets corrode, service cables crack where they meet the weatherhead, and main disconnects wear. In South Florida, heat, salt air and storms add stress. An upgrade can mean a larger service, or simply a new one of the same size that replaces worn equipment. Both are common, and both begin with understanding what you have now.

24 Hour Electrician Near Me electricians reviewing a commercial electrical panel

Signs a home has outgrown its service

Overloaded services rarely announce themselves with a single dramatic event. They show up as patterns. Lights dim when the air conditioner starts. The main breaker trips when several large appliances run together. Breakers in the panel are full, with tandem breakers squeezed into spaces, and there is no room for another circuit. Extension cords snake through the house because outlets are scarce.

Other signs are physical. A main disconnect that feels hot, a meter socket that is discolored or cracked, a service cable that frays at the weatherhead, or a panel with rust or water marks all suggest the service equipment needs replacement. Some of these are urgent and should be treated as such.

Age is another clue. Homes built decades ago commonly have services sized for a time when households used far less power. A house wired for a modest service may now be running central cooling, electric cooking and several large appliances. Our page on choosing electrical service size explains how technicians think about the capacity a home needs.

  • Lights dim or flicker when large appliances start
  • The main breaker trips when several loads run together
  • No spare spaces in the panel, with many doubled-up breakers
  • Warm, discolored or rusted service equipment
  • A planned addition, pool, EV charger or new air conditioner

What an upgrade includes

A service upgrade is a package of parts that work together. It usually includes a new meter socket, new service entrance conductors or cable, a new or upgraded weatherproof mast or underground conduit, a main disconnect, and a new main panel or load center. The grounding and bonding system is brought up to current expectations, which often means new grounding electrodes and connections.

The panel is part of the story but not the whole story. Replacing only the panel while leaving an old meter socket and worn service cable in place leaves weak parts in the chain. A technician will advise whether the whole entrance is being replaced or only part, and why. Our page on electrical panel repair and replacement explains the panel side in more detail.

Related equipment may need attention. If the service is increased, the branch circuits stay the same, so the main change is capacity at the entrance, not the wires inside the house. But a bigger service may reveal limitations further downstream, such as overloaded or aging circuits. A good technician looks at the whole system and tells you where the next weak point is, even if you decide to handle it later.

ComponentWhat happens during an upgrade
Service conductorsReplaced or extended to suit the new capacity
Mast or underground conduitReplaced, braced or reworked to fit the new service
Meter socketReplaced with a unit sized to the service, set per the utility's rules
Main disconnectNew device that shuts off the whole house
Main panelNew panel with enough spaces for current and future circuits
Grounding and bondingNew or verified electrodes and connections

How the utility and the electrician share the work

A service upgrade is a joint effort. The electrician handles the equipment on the customer's side: the mast, the meter socket, the main disconnect, the panel and the grounding. The utility handles its own lines, the connection at the pole or transformer, and the meter itself. In most of South Florida the utility is FPL, and in some municipalities local utilities handle service, so the process can vary by address.

The usual sequence is coordination. The electrician arranges the permit and any request the utility requires, schedules the inspection, and then the utility disconnects power, reconnects it after approval, and sets or reconnects the meter. The utility decides when it can do its part, and that timing is outside the electrician's control. Our guide to utility meter and service responsibilities explains who owns what.

Because of this, a service upgrade involves waiting for others. Power may be off for part of a day, and the date depends on the utility's schedule and the inspection. A responsible electrician explains this at the beginning and tells you what you need to arrange, such as a way to keep food cold or medical equipment running while power is off. Make sure you understand the sequence before work starts.

Overhead service or underground service

Homes receive power in one of two main ways. Overhead services bring cable from a pole or the street to a mast on the house, ending at a weatherhead where the cable enters a conduit. Underground services run from a transformer or pedestal through buried conduit to the meter socket. Each type has its own considerations during an upgrade.

Overhead services are exposed to wind and storms. Masts bend, weatherheads pull away and trees damage cables. When upgrading, the mast may need to be replaced or braced, and clearances to the roof, driveway and windows must be correct. Our page on service mast and weatherhead repair explains what can go wrong.

Underground services avoid wind damage but face water and soil. Conduit can crack or fill with water, and in flood-prone areas that is a concern. Converting from overhead to underground is a separate project that involves trenching, new conduit and coordination with the utility. If a property is being renovated, ask whether it is a good time to consider that change, and whether the utility and local rules allow it.

  • Overhead: mast, weatherhead and clearance are the focus
  • Underground: conduit condition, depth and water intrusion matter
  • Changing from one type to the other is a larger project with the utility
  • Storm-prone areas should weigh mast bracing and flood exposure

Choosing the new capacity

Choosing the size of a new service is a calculation, not a guess. The technician adds up the loads in the home using accepted methods: lighting, outlets, large appliances, air conditioning, water heating, pool equipment, and so on, with allowances for loads that do not run all at once. The result suggests a service size that meets the present need with room for reasonable additions.

Future plans matter. A car charger, a pool, an addition, an accessory suite, solar and batteries all add to the demand. If you expect any of these in the next few years, it makes sense to size the service accordingly. Installing a service that is too small and upgrading again soon is wasteful, while installing one that is much larger than needed adds cost without benefit.

Load management can sometimes reduce the size needed. Devices that limit simultaneous use of large loads, or smart panels that shed lower-priority circuits, help a modest service handle more equipment. Our page on smart panels and load management explains how those work. A technician can describe whether that route fits your home or whether a straightforward larger service is better.

Permits, inspections and the utility's requirements

A service upgrade is permitted work. The permit is pulled through the local building department, and an inspection is required before the utility will restore or connect power. Some jurisdictions also require a utility release or a specific form. The requirements depend on the city and the utility, and the electrician should know the local procedure.

Inspection standards cover the physical installation: the height and mounting of the meter socket, the type and clearance of the mast, the sizing of conductors, the grounding electrodes and the labeling of the panel. An inspector may also check that bonding is correct and that the work matches the permitted plan. Failing an inspection delays reconnection, so a careful installation matters.

Associations and condominiums add steps. In a multi-unit building, the service may be shared or part of the common elements, and changes require association approval. Our guide on electrical permits in South Florida describes the general process. In every case, make sure the permit is in place before work starts, and keep the final inspection record with your property papers.

What the day of the upgrade looks like

Most upgrades involve a planned power outage. The electrician and utility coordinate so that power is off for as short a time as practical, but the length depends on the amount of work and the sequence of steps. Expect the house to be without power for part of the day, and sometimes longer if the utility's schedule or the inspection runs behind.

Prepare for it. Plan how you will handle refrigeration, medical needs, remote work and pets in the heat. Unplug sensitive electronics, since power returning can produce surges. Clear a path to the panel and the meter, and make sure the crew can reach the exterior wall and the interior panel location. Move vehicles and items that may be in the way.

After the work is complete and inspected, power is restored and the new equipment is tested. Walk through the house, check that circuits work, and confirm that the panel is labeled. Reset clocks, check any equipment that does not restart on its own, and keep the paperwork. If something seems off after reconnection, such as flickering or a dead circuit, tell the technician right away.

  • Plan for a power-off period and how to cope with it
  • Unplug sensitive electronics before the outage
  • Clear access to the meter, mast and panel
  • Keep the permit and final inspection records
  • Report any odd behavior right after power returns

Hurricane season, flooding and timing

Timing a service upgrade around hurricane season is smart. Weak masts, corroded meter sockets and aging service cable are the parts that fail in storms. Replacing them before a storm, instead of after, avoids long waits when the utility and electricians are overwhelmed. Many owners schedule upgrades in the quieter months for exactly this reason.

Flood exposure should be considered. In flood-prone areas, the meter socket and main panel may be installed higher than usual so that rising water does not reach them. Local rules may also affect height and location. Our guide on flood zone electrical planning explains these decisions. Salt air near the coast calls for corrosion-resistant equipment and careful sealing of penetrations.

If a storm has already damaged your service, do not try to repair it yourself. A leaning mast, a pulled weatherhead or a hanging meter box can be live. Stay away, keep others away, and call the utility if lines are down, and call 911 if there is fire or immediate danger. Our guide on electrical safety after a hurricane lists what to do in what order.

Mistakes to avoid when upgrading a service

The first mistake is upgrading the service in pieces without a plan. Replacing a panel this year, a meter socket next year and a mast after the next storm means paying for several outages, several inspections and several rounds of utility coordination. If the whole entrance is aging, doing it as one project is often simpler, even if the steps are phased by budget.

The second is sizing for today only. A service chosen to just cover the present load may be outgrown the moment a car charger or a new air conditioner is added. Talk about what you expect in the next several years before settling on a capacity, and ask the technician to explain the reasoning behind the number.

The third is skipping the paperwork. Unpermitted service work can cause the utility to refuse reconnection, create trouble with insurance, and cause problems when you sell. A permit is not a nuisance; it is the record that the work was reviewed. Keep the inspection sign-off with your deed papers, and give a copy to your insurer if they ask.

  • Replacing parts one at a time with no overall plan
  • Choosing a capacity that ignores planned additions
  • Working without a permit or without telling the association
  • Assuming the utility's timeline is the same as the electrician's
  • Forgetting to label the new panel and keep the records

Getting started and what to have ready

Start by collecting a few facts: the age of the home, the current panel size if it is labeled, any appliances or additions you plan, and any problems you have seen. A photo of the panel and the meter helps the technician understand what you have. Note whether power comes overhead or underground.

Expect a site visit. A service upgrade cannot be responsibly quoted without seeing the equipment, the location of the meter and panel, the routing and the access. The service call charge for the visit is explained on the phone before dispatch, so there is no surprise. Quotes are given only by phone after the technician understands the property.

When you are ready to talk through your home's service, call. Describe what you have noticed and what you plan to add. The technician will explain what is likely involved, what the utility will handle, and what you can do to keep the project moving smoothly.

Questions people ask

How do I know if I need a bigger service?

Common signs include dimming lights when large appliances start, a main breaker that trips, a full panel with no room for new circuits, and plans for a pool, addition or car charger. A technician calculates the actual load of the home and recommends a size, so you are not left guessing.

Who does what during a service upgrade?

The electrician handles the customer-side equipment: mast, meter socket, main disconnect, panel and grounding. The utility handles its own lines, the connection and the meter. The electrician coordinates the permit and inspection, and the utility reconnects power after approval. Timing for the utility's part is outside the electrician's control.

How long will my power be off?

It depends on the work and on the utility and inspection schedule, so the technician explains the plan in advance. Prepare for part of a day or more, and arrange for refrigeration, medical needs and anything else that cannot go without power. Do not assume a fixed duration without confirmation.

Is a permit required?

Yes. A service upgrade is permitted work, and the local building department inspects it before the utility reconnects power. Requirements vary by city and utility, and your electrician should know the local procedure. Keep the permit and inspection records with your property papers.

Can I just replace the panel and keep the old meter socket?

Sometimes, but it depends on the condition of the meter socket, the service cable and the grounding. Leaving worn parts in place can undermine a new panel. A technician checks the whole entrance and tells you which parts are sound and which should be replaced together.

How is a service upgrade priced?

Quotes are given only by phone. Because a service upgrade involves the meter, mast, panel, permit and utility coordination, it begins with an on-site visit. There is a service call charge for that visit, and it is explained on the phone before dispatch, so you know it ahead of time.

Talk to 24 Hour Electrician Near Me

For "Upgrading the Main Electrical Service", a phone call comes first. Describe the circuit, the breaker or the equipment, and we will talk through the safe next steps and whether the job needs an on-site look.

Related pages

  • Panel Repair: Guide to electrical panel repair, replacement and capacity upgrades in South Florida: what an evaluation covers, permits and what to prepare before a visit.
  • Subpanel Installation: Adding a second electrical panel for a garage, addition or pool equipment without replacing the main panel: sizing, feeder wiring, grounding and permits.
  • Meter Socket: Who does what when a meter socket is damaged: the owner, the electrician and the utility, how power is disconnected and restored, and how to plan the repair.
  • Service Size: How 100, 150 and 200 amp electrical services fit different South Florida homes, and what changes the answer: AC, EV charging, pools and additions.
  • Service Equipment: The parts between the utility drop and your panel, the meter socket, mast, disconnect and main breaker, and which ones the owner must maintain.
  • Mini-Split Wiring: How power is run to ductless mini-split units: dedicated circuits, disconnects, wire sizing, and what a technician checks before connecting the system.

Talk through the electrical service you need.

Request service
Call (754) 226-1874