What service size means
Electrical service size describes how much current your home's main equipment is designed to carry. It is set by the rating of the main breaker or disconnect, the size of the service conductors that run from the utility connection, and the rating of the meter socket and panel. All of these parts must match, because the weakest part limits the system.
Amperage is a measure of current. A larger service, such as 200 amps, can supply more simultaneous electrical demand than a smaller one, such as 100 amps. It does not mean you use that much power all the time. Most homes use only a fraction of their service capacity at any moment, and the question is whether there is enough headroom for the busiest realistic moment, such as a hot afternoon with the air conditioner, range, dryer and water heater all running.
Service size is also different from the size of individual circuits inside the home. Each branch circuit has its own breaker, and the total of all those breakers can exceed the service rating because not everything runs at once. A qualified person uses a load calculation, a structured method defined by the electrical standard, to determine whether a service is adequate. That calculation is more reliable than a rule of thumb.

What a 100 amp service typically serves
A 100 amp service was common in homes built decades ago, particularly smaller houses, older bungalows, and condominium and apartment units. It can serve a modest home with gas appliances or a few electric loads and one central air conditioner. Many older South Florida homes still operate with this size, and some function without problems.
The limits show up when the home adds loads. A second air conditioner, an electric range, an electric dryer, an electric water heater, a pool pump, an EV charger and a hot tub together can exceed what a 100 amp service can supply. Signs of strain include breakers that trip when several appliances run together, lights that dim when the air conditioner starts, and a main breaker that feels hot or trips.
Not every strain sign means the service is too small. Our page on lights dimming when the AC starts explains other causes. A technician can assess whether the issue is the service, the wiring, the connections or the equipment before recommending any change.
- Often found in smaller or older homes and many condominium units
- Suited to modest loads with limited electric heating or cooking
- May be tight if you add EV charging, a pool or a second air conditioner
- Panels may be older and have limited breaker spaces
What a 150 amp service typically serves
A 150 amp service sits in the middle. It was used in mid-sized homes and as a modest upgrade from 100 amps. It can serve a home with central air conditioning, an electric range and dryer, and a few additional loads, provided the load calculation supports it. It leaves moderate headroom for growth.
In practice, 150 amp services are less common in new construction than 200 amps, because builders and owners tend to value the extra capacity. If you already have a 150 amp service and it works well, there is no reason to replace it just because it is not 200. If you are planning significant new loads, the load calculation will tell you whether it is enough.
One point to confirm is whether every component is rated for the service. A home may have a 150 amp main breaker but an older meter socket or conductors that limit the real capacity. A visual look at the equipment and a review of labels are part of what a technician does when assessing service.
What a 200 amp service typically serves
A 200 amp service is the common standard for modern single-family homes, and it is a typical choice when upgrading an older home. It supports central air conditioning, electric cooking, an electric dryer, an electric water heater, a pool, a modern home office and a Level 2 EV charger together in many homes, again subject to a load calculation.
The advantage is headroom. Loads added over the years do not strain the system as quickly, and an EV charger or a heat pump does not require another upgrade. Many owners who replace a panel for other reasons choose to step up to 200 amps at the same time because much of the labor is already in place. Our page on main service upgrade explains what that work involves.
A larger service is not automatically better for every home. A small condominium with gas appliances and no plans to add large loads may never use the extra capacity, and some buildings limit what an individual unit may do. The right size is the one the load calculation supports with a reasonable margin for your realistic plans.
Larger services for larger loads
Some homes need more than 200 amps. Large homes with multiple air conditioning systems, guest houses, a pool and spa, an outdoor kitchen, a workshop, and several EV chargers can approach or exceed what 200 amps can serve. In those cases, 300 or 400 amp services, or two panels fed from a single service, may be appropriate.
Larger services involve more than the panel. The meter socket, service conductors, the utility's equipment and the mast or underground lateral may all need to change, and the utility has its own requirements and schedules. Our page on meter socket replacement and our guide to utility meter and service responsibilities explain which parts belong to the owner and which to the utility.
Because these projects are complicated, they begin with a conversation and an on-site visit. We do not offer prices on this website, and quotes are given only by phone.
What changes the answer for your home
Several features of a South Florida home push the load upward. Central air conditioning is the largest, because a home may run it much of the year. Electric water heaters and dryers are large continuous or intermittent loads. Pools add pumps, heaters and lighting. Kitchens with electric ranges and ovens draw heavily. Home offices and entertainment systems add many small loads.
Future plans matter as much as current loads. If you intend to buy an EV, add a second story or an accessory unit, finish a garage, install a generator or add solar and battery storage, say so during the assessment. It is easier and less disruptive to size the service for those plans once than to upgrade twice.
Our pages on EV charger installation, ADU and guest suite electrical and home addition electrical wiring describe how each affects the service.
| Addition or load | Effect on service planning |
|---|---|
| Second central air conditioner | Adds a large motor load, check starting demand |
| Electric dryer or range | Adds large dedicated circuits |
| Pool pump and heater | Adds continuous and heating loads |
| Level 2 EV charger | Adds a long-running high current load |
| Home addition or ADU | Adds lighting, cooling and appliance loads |
| Generator or battery system | Changes how the service is connected |
| Solar array | Adds a generation source with its own connection rules |
How a load calculation works
A load calculation is a structured procedure that adds up the expected electrical demand of the home using rules from the electrical standard. It starts with the floor area, which sets a base lighting and general-purpose load, then adds fixed appliances such as the range, dryer, water heater and air conditioning, then applies demand factors that recognize not everything runs at once.
The result is a number in amps that you compare with the service size. A home whose calculated load is comfortably below its service rating has headroom. A home whose calculated load approaches or exceeds the rating needs a larger service or a plan to manage loads. Technicians can also use meter data or a monitoring device in some cases, but the standard calculation is the baseline.
You do not need to do this arithmetic yourself, but it helps to know that a trustworthy recommendation to upgrade should be backed by one. Be cautious of a recommendation that jumps to a bigger service with no discussion of loads. See also our page on wire gauge and breaker sizing for how the pieces inside the home relate to the service.
Alternatives to a bigger service
Sometimes the answer is not a larger service. Load management devices can share capacity between large loads so they do not run at the same time. For example, an EV charger can reduce or pause its charging when the dryer or oven is running. A smart panel can monitor and control circuits. Our page on smart panels and load management explains how those work.
Switching a major appliance to a different type may help, such as a heat pump water heater in place of a resistive one, though that is a decision to make with all the facts. Adding a subpanel can solve a shortage of breaker spaces without changing the service; see subpanel installation. A subpanel does not increase the service capacity, though. It only distributes what the service provides.
The best approach is to understand what actually limits your system: the number of breaker spaces, the capacity of the service, or the wiring on specific circuits. Each of these has a different fix, and a technician can tell you which one applies.
Permits, the utility and the timeline
A service upgrade is a permitted project in Florida municipalities. It typically requires an electrical permit, an inspection, and coordination with the utility, which must disconnect and reconnect its service at the right moments and may need to inspect or approve the work. The details vary by location, so the contractor handling the work should explain the process for your address.
Plan for a period without power on the day of the change. A well-organized contractor tells you in advance when the power will be off, helps you protect sensitive equipment, and coordinates the reconnect. Residents of condominiums and buildings with shared equipment must coordinate with the association or management; see our page on condo association electrical approvals.
We do not promise specific timelines on this page, because schedules depend on the municipality, the utility and the scope of work. Ask for the process to be explained on the phone, and ask what you need to prepare.
Questions to ask and next steps
Ask the technician what the main breaker rating is, what the meter socket and conductors are rated for, and what the load calculation shows. Ask what the options are, including whether a smaller change would solve the problem. Ask how permitting and the utility connection will be handled.
Bring information when you call: the age of the home, the main breaker rating if visible on the label, the brand of the panel, the major appliances, and your plans for the next few years. A photo of the panel exterior and the meter can help. Do not open the panel cover.
Quotes are given only by phone. Because service work is complicated, an on-site visit is part of the process, and there is a service call charge, explained before dispatch. Call, tell us what you plan, and we will explain what the right size might involve.
- Note your main breaker rating and panel brand from the outside labels
- List major electric loads and anything you plan to add
- Describe any symptoms such as dimming lights or tripping breakers
- Call and discuss the plan with a technician
- Schedule an on-site visit for a load review when the job calls for it
- Confirm permit and utility steps before work begins
Questions people ask
Is a 200 amp service always better than 100 amps?
Not always. A small home or condominium with modest loads may never use the extra capacity. A 200 amp service gives more headroom for air conditioning, EV charging, pools and additions, but the right size comes from a load calculation and your plans. A technician can explain whether your current service is adequate.
How do I know what size service I have?
Look at the main breaker at the top of your panel, which usually shows the rating in amps, such as 100 or 200. The meter socket and service conductors also have ratings. Do not remove the panel cover to look. A photo of the outside of the panel and the meter helps a technician confirm the details.
Do I need a bigger service for an EV charger?
Sometimes. It depends on the size of your service, your existing loads and the charger you choose. A load calculation shows whether there is room. Load management devices can also let a charger share capacity with other large loads, which may avoid an upgrade. A technician can review the options for your home.
Does a service upgrade require a permit?
Yes, service upgrades are generally permitted work that involves an inspection and coordination with the electric utility. Requirements vary by city and county, and condominiums may need association approval. A qualified electrical contractor should explain the process for your address and handle the permit and the scheduling of the inspection.
Will a subpanel increase my service capacity?
No. A subpanel adds breaker spaces and distributes power from the existing service, but it does not increase how much the service can supply. If the main service is the limit, only a larger service, or load management, addresses it. A technician can tell which of these your home needs.
How do I get a price for a service upgrade?
Quotes are given only by phone. Service work is complicated, so it usually begins with a conversation and an on-site visit to review the meter, panel and loads. There is a service call charge, and we explain it on the phone before any technician is dispatched. We do not publish prices on this website.
For "Choosing the Right Electrical Service Size", a phone call comes first. Describe the circuit, the breaker or the equipment, and we will talk through the safe next steps and whether the job needs an on-site look.
Related pages
- Service Upgrade: When a home outgrows its electrical capacity: replacing the service entrance, meter base and main disconnect, how the utility fits in, and what to expect.
- Meter Socket: Who does what when a meter socket is damaged: the owner, the electrician and the utility, how power is disconnected and restored, and how to plan the repair.
- Subpanel Installation: Adding a second electrical panel for a garage, addition or pool equipment without replacing the main panel: sizing, feeder wiring, grounding and permits.
- Smart Panels: Circuit-level monitoring and load-shedding devices explained for homes with EV chargers, heat pump equipment and backup power, and how they fit a panel.
- Wire and Breaker Size: How wire gauge and breaker size work together to keep circuits safe, why a bigger breaker is never a fix, and what to check when a circuit trips.
- After the Hurricane: Post-storm electrical hazards: damaged service equipment, flooded panels, generator misuse, and how to know when it is safe to restore power to a home.
Reading your own usage before you decide on a bigger service
Deciding whether a larger service is justified begins with how your household actually behaves. Think about the busiest hour of a hot summer evening: the air conditioner running, someone cooking, a dryer going, the water heater recovering, and a car charging. If the lights dim or a breaker trips in that window, that is useful evidence. If nothing complains even on the worst day, the existing service may already be adequate. Notes kept over a few weeks, including which circuits trip and when, give a technician a clearer starting point than a general feeling of strain.
Plans matter as much as habits. A kitchen remodel, a home addition, a pool, a second air conditioner, or an electric vehicle each add load that today's panel may never have been sized to carry. Writing these plans down before any calculation is done prevents the common mistake of upgrading just enough for today and then needing another change within a few seasons. Equally, it prevents overbuilding for a purchase that never happens. The goal is a service that fits a realistic picture of the next several years. Remember that South Florida heat and moisture can make an ordinary problem show up faster than it would in a drier climate.
Bring your notes and your electric bills to the first conversation, along with a list of the appliances you own or intend to add. A technician can compare that picture against the equipment already on the wall and explain the scope before any work begins. Ask what is being replaced, what stays, and what the utility and the local building department will have to approve. Because every property differs, nothing here replaces an on-site look. Call us to discuss your situation and confirm availability in your area. Every property has its own history of repairs and additions, which is why general guidance can only take you so far.
