Residential and commercial electrical servicesCall (754) 226-1874

Services

Repairing a Leaning Service Mast

When a storm bends the pipe that carries power to your house, or pulls the cable away from it, the repair is split between you and the utility. This page explains what the mast and weatherhead are, what is dangerous, and how the repair is coordinated.

24 Hour Electrician Near Me electrician at work in a South Florida property

What the service mast and weatherhead are

In an overhead service, power reaches your house from a pole or street line through a cable called the service drop. That cable attaches to the house at a point high enough to clear the roof and the yard, and then runs down into the meter socket. The pipe that carries the customer's wires up above the roof or to the attachment point is the service mast, usually a rigid metal conduit.

At the top of the mast sits the weatherhead, a curved fitting that keeps rain from running down into the conduit. The wires from the utility drop come through the weatherhead, and a loop of slack called a drip loop lets water drip off before it reaches the opening. Below the weatherhead, the conductors run down the mast to the meter socket and then the main panel.

Each part has a job. The mast holds the weight and tension of the service drop. The weatherhead keeps water out. The wires inside carry the whole house's power. If any of these fails, the result can be a loss of power, a shock hazard or water entering the electrical system. That makes damage to the mast area something to treat carefully, not casually.

24 Hour Electrician Near Me technician unloading tools from a branded van at a South Florida home

How storms and age damage the mast

Wind is the main cause. Hurricane-force gusts push on the service drop and trees, and the load is transferred to the mast. A mast that is not properly braced can bend, lean or even pull away from the wall or roof. Falling branches and debris can strike it directly. Even without a storm, years of tension and corrosion can weaken the connection points.

Corrosion is common in South Florida. Humid air and salt weaken metal conduit, brackets and straps, and the point where the mast passes through the roof is especially prone to rust and leaks. A mast that is leaning slightly may have been like that for years, or may have started leaning in the last storm, and it is hard for an owner to tell which.

Other causes include roof work and vehicles. Roofers who replace shingles sometimes disturb the mast or its flashing. High trucks and boat trailers can snag low service cables. A homeowner who sees a leaning mast, a sagging service cable or a weatherhead that points the wrong way should treat it as a priority and have it looked at, even if the lights are still on.

  • Mast leaning, bent or pulling away from the building
  • Weatherhead cracked, loose or pointing upward
  • Service cable sagging low or stretched tight
  • Rust, leaks or damaged flashing where the mast meets the roof
  • Tree limbs resting on the service cable or mast

Safety first: what to stay away from

Assume that any wire reaching your house is live. The service drop carries the utility's full voltage, and it can be dangerous even if the cable looks insulated or has been bent or damaged. A pulled weatherhead can leave live conductors hanging, exposed to touch and to water. A downed or sagging line may arc on contact with wet ground, a fence, a car or a person.

Stay well back from any damaged line, and keep children and pets away. Do not touch or move wires, branches touching wires, or anything that touches wires. Do not stand in standing water near damaged lines. If a line is down or if there is fire, smoke or sparking, call 911, then call the utility's emergency line to report it. Do not try to cut a tree off a line yourself.

Never climb onto a roof or use a ladder near a service mast. Metal ladders conduct electricity, and wind can shift a ladder into a line in a second. Our guide to a power line down at your property explains what to do in order. Even if you think a damaged mast is only a cosmetic problem, treat it as a hazard until a qualified person has inspected it.

Who handles which part of the repair

The line between the owner's and the utility's responsibility runs near the weatherhead. In general, the utility owns the service drop, the cable that runs from its pole or transformer to your house, and its connection at the pole. The owner owns the mast, the weatherhead, the wires inside the mast and everything downstream. The utility handles the drop, and the electrician handles the customer side.

That division means the electrician cannot simply fix everything. When the mast needs replacement, the utility typically must disconnect the drop so the electrician can safely work, and then reconnect it afterward. The utility also decides how and when to do its part, and it may insist on certain requirements for the attachment point and the clearance of its cable. Our guide to utility meter and service responsibilities explains this boundary in more detail.

In practice, you may need two calls: one to the utility to report the damage and request a disconnect, and one to an electrician to repair the mast and weatherhead. An experienced electrician coordinates between the two. In an emergency, the utility may disconnect first for safety, and the electrician repairs after. The order depends on the hazard and on the utility's procedures.

PartUsually owned and repaired by
Service drop from the pole to the houseUtility
Connection at the pole or transformerUtility
WeatherheadOwner, repaired by the electrician
Service mast and bracingOwner, repaired by the electrician
Conductors inside the mast and meter socketOwner, repaired by the electrician
Disconnect and reconnect of the dropUtility, coordinated with the electrician

What a repair involves

A repair starts with assessment. The electrician looks at the mast, the weatherhead, the roof penetration, the brackets, the conductors and the connection to the meter socket, and decides what must be replaced. A slightly bent mast with sound conductors may be repaired and braced. A badly bent or corroded mast is replaced. A pulled weatherhead is replaced along with any damaged conductors.

Replacement work typically involves removing the old mast, installing a new one of the right size and type, fitting a new weatherhead, pulling or splicing conductors as needed, and sealing the roof penetration so that it does not leak. Bracing or supports are added to meet the load and clearance requirements. Where the roof passes through, flashing is installed so that rain stays out.

The utility's part comes before and after. The drop is disconnected before work starts, and reconnected after inspection. If the mast is moved or raised, the utility may need to check clearances for its cable. After reconnection, the electrician and the owner check that everything works, and look for water, odors or signs of heat. If the roof was touched, a roofer may be needed for the finish.

  1. Safety assessment and report to the utility if the drop is damaged
  2. Permit and scheduling of the utility's disconnect
  3. Utility disconnects the service drop
  4. Electrician replaces or repairs the mast, weatherhead and conductors
  5. Roof penetration sealed and flashing restored
  6. Inspection by the local building department
  7. Utility reconnects the drop and restores power

Clearances, height and bracing requirements

Rules govern how high the service cable must be above the roof, the ground and driveways, and how far the mast may extend above the roof without bracing. These ensure that the cable cannot be reached from the roof, that vehicles can pass underneath, and that the mast can bear the load of the cable without bending.

The result is that the new mast is not always the same as the old one. If the old installation did not meet current clearances, the repair may need to raise the mast or add bracing. If the roofline has changed because of an addition or a new roof, the attachment point may need to move. A technician checks these distances and explains what is needed for approval.

The inspector and the utility both look at the installation. They may check the mast size and type, the strapping, the weatherhead orientation, the drip loop and the roof flashing. Meeting these requirements at the start avoids rework. Our page on main service upgrades describes the larger project that sometimes includes a new mast.

  • Cable height above the roof, yard and driveway
  • Mast height above the roofline and the need for bracing
  • Strapping and supports that carry the load
  • Weatherhead orientation and drip loop
  • Flashing at the roof penetration

Water intrusion and roof leaks

The mast is a path through the roof, and any path is a potential leak. If flashing fails or the mast moves, rain can run down the conduit or around it into the attic and the meter socket. Water in the electrical system is dangerous, and it causes corrosion that can damage the meter socket, the main breaker and the panel.

Signs include water stains on the ceiling near the mast, rust streaks on the mast, water in the meter socket or panel, and tripped breakers during rain. Our page on water in the electrical panel explains what to do if water has reached the panel. Do not open the panel or meter yourself if you suspect water.

Repair should treat both the electrical and the roofing sides. The electrician replaces the damaged conductors and seals the entry points. The roof flashing around the mast is repaired or replaced, which sometimes requires a roofer. Coordinating the two trades avoids a situation where the electrical work is done but the leak continues, or vice versa.

After a hurricane: what to expect

After a major storm, many homes need mast and weatherhead repair at the same time. Utilities and electricians are stretched, and the wait can be long. Prioritize safety. If the mast is bent and the cable is pulled, do not use the electricity in the house until the situation has been made safe, even if the lights seem to work.

Report damage to the utility, because they must reconnect or repair the drop. Then contact an electrician for the customer-side work. Take photos from a safe distance for insurance. Many insurers cover storm damage to the mast and weatherhead, and documentation helps. Keep any reference numbers from the utility.

Temporary measures may be possible in some cases, but they should be left to professionals. Our guide to electrical safety after a hurricane explains the order of steps and what to avoid. Owners in areas such as Pompano Beach, Hollywood and Deerfield Beach, where storm risk is well known, can reduce future damage by having masts inspected and braced before the season.

Tree trimming, roofing work and preventing the next failure

Many mast failures start with something other than wind alone. A tree limb that rubs the service cable for months wears through the insulation. A palm frond that falls across the line adds a sudden pull. A roofing crew that replaces tile or shingles may bump the mast, loosen the flashing or leave the bracing weaker than before. Prevention is largely about managing these neighbors.

Trees near service lines should be trimmed by the utility or by a qualified line-clearance contractor, not by the homeowner. Cutting branches that touch or lean toward live wires is dangerous, and in many places the utility handles trimming near its drop. Ask the utility about its trimming policy. Keep fast-growing trees and palms away from the attachment point as they mature.

Before roof work, tell the roofer where the mast is and ask them to leave it undisturbed. If the mast must be moved or the roof re-covered around it, bring in the electrician first, because the utility may need to disconnect while the work is done. After any roof work, look from the ground at the mast and weatherhead for a change in angle, a gap in the flashing or a loose strap. A quick look can catch a problem before the next storm does.

  • Leave trimming near the service drop to the utility or line-clearance professionals
  • Tell roofers where the mast is and have the electrician involved if it must move
  • Check the mast and weatherhead from the ground after any roof work
  • Have masts inspected and braced before the hurricane season begins
  • Keep ladders, antennas and pool poles well away from the service cable

Permits, inspections and condominium cases

Replacing a service mast is permitted work in most jurisdictions, and the building department inspects it before the utility reconnects. Requirements vary by city, and the electrician should know the local procedure. In emergencies some cities allow certain repairs to proceed with an expedited process, and the electrician can explain what applies.

In townhouses and condominiums, the mast and the service may be part of the building's common elements. The association may own the equipment or control the repair. Check your documents and notify management before arranging work. Attached homes may share a roofline or a wall, which affects how a mast can be braced and how the roof is handled.

Keep the final inspection record. It shows that the work met the standards and is useful for insurance claims and for selling the home. If the utility had to disconnect and reconnect, keep any reference numbers. These records document the repair and protect you if questions arise later.

Preparing for the call and the visit

When you call, describe what you see: leaning mast, pulled weatherhead, sagging cable, water inside, or storm damage. State whether power is on or off and whether the utility has been contacted. Explain whether the house is single-family or attached, and whether the roof is tile, shingle or flat.

Take photos from the ground at a safe distance. Do not climb or approach damaged lines. Move vehicles and equipment away from the area so the crew can work. Make sure the technician can reach the mast and the meter socket, and clear any plants or items in the way.

Quotes are given only by phone, and mast work starts with an on-site assessment. There is a service call charge for that visit, and it is explained on the phone before dispatch. If you think the situation is hazardous, say so on the call. Call to describe the damage and arrange a visit, and the technician will explain the steps and what the utility must do.

Questions people ask

Is a leaning service mast an emergency?

It can be. A mast that is leaning or pulled can strain the cable and weatherhead, expose live conductors or let water in. Stay away, keep others away and report it. If there is sparking, smoke, fire or a line on the ground, call 911 and then the utility's emergency line.

Who repairs the service drop, me or the utility?

The utility owns and repairs the service drop and its connection at the pole or transformer. The owner owns the mast, weatherhead and everything downstream, and an electrician repairs those parts. The electrician coordinates with the utility so power can be safely disconnected and restored.

Can I straighten the mast myself?

No. The conductors in and around the mast are live, the utility cable is attached, and the work requires disconnecting power through the utility. Attempting it risks electric shock and fall injury. Keep ladders and tools away from the area and have a qualified electrician handle it.

Will I need a permit for a mast repair?

Usually yes. Mast and weatherhead replacement is permitted work in most South Florida jurisdictions, with an inspection before the utility reconnects power. Procedures differ by city, and some allow expedited handling after storms. Your electrician can explain what applies and handle the paperwork.

Why is my roof leaking near the mast?

The mast passes through the roof, and the flashing around it can fail or shift when the mast moves. Water can then run into the attic or down the conduit. Do not open the meter or panel if you suspect water. The repair usually involves both the electrician and a roofer.

How is a mast repair priced?

Quotes are given only by phone. Mast work starts with an on-site assessment, since damage can extend to the weatherhead, conductors and roof. There is a service call charge for that visit, and it is explained on the phone before dispatch, so you know it ahead of time.

Talk to 24 Hour Electrician Near Me

If "Repairing a Leaning Service Mast" sounds like your problem, call and describe what you see, hear or smell at the panel, the outlet or the fixture. We explain what the work involves, and some jobs need a visit before a quote.

Related pages

  • Service Upgrade: When a home outgrows its electrical capacity: replacing the service entrance, meter base and main disconnect, how the utility fits in, and what to expect.
  • Meter Socket: Who does what when a meter socket is damaged: the owner, the electrician and the utility, how power is disconnected and restored, and how to plan the repair.
  • Downed Power Line: A downed power line is life-threatening. Learn how to stay clear, who to call first, and what electrician work follows on your side of the meter.
  • After the Hurricane: Post-storm electrical hazards: damaged service equipment, flooded panels, generator misuse, and how to know when it is safe to restore power to a home.
  • Meter Responsibilities: Where utility equipment ends and the property owner's equipment begins at the electric meter, and who repairs what when something is damaged.
  • Smart Switches: Adding smart switches and dimmers to existing boxes: neutral wire availability, load compatibility, three-way setups and how to choose a hub or no-hub system.

Talk through the electrical service you need.

Request service
Call (754) 226-1874