What three-phase power is, in plain terms
Homes in most of the country receive single-phase power, which is delivered over two hot conductors. Many commercial and light industrial buildings receive three-phase power, delivered over three hot conductors whose voltages peak at different moments. The result is smoother delivery of power, which suits large motors, compressors, elevators, pumps, commercial kitchen equipment and machinery. It also allows smaller conductors to carry large loads efficiently.
A three-phase service is typically described by its voltage arrangement, such as a configuration that gives you both a lower voltage for lighting and outlets and a higher one for motors. Which arrangement your building has determines what equipment can run on it. Putting the wrong equipment on the wrong supply is a common reason for repeated failures.
Because many loads in a building run on only one of the three phases, such as lights, outlets and small equipment, and others use all three, the system has to be both balanced and complete. If something goes wrong with one phase, the effects may be confusing. Lights may still work, while a large motor refuses to start or runs hot.

Single-phasing: when one phase is lost
The most damaging condition is a lost phase, sometimes called single-phasing. One of the three conductors is no longer delivering power, perhaps from a blown fuse, a failed breaker pole, a loose or burned connection, a broken wire at the utility or a failed transformer connection. The remaining two phases keep supplying whatever they can.
Three-phase motors react badly. A motor that is running when a phase is lost may keep turning but draws much more current on the remaining phases, overheats and may burn out. A motor that is stopped will often hum and fail to start. Air conditioning compressors, pumps and fans are frequent victims. Many modern controls include phase-loss protection to switch equipment off, and when it trips it is doing its job.
If a motor hums but does not start, or if some equipment works while three-phase equipment does not, turn the equipment off to avoid damage and call. Do not keep trying to restart it. The page on power loss troubleshooting explains how a technician approaches partial outages, and half the house has no power describes the residential version of a similar problem.
Voltage imbalance and low or high voltage
Even when all three phases are present, they may not be equal. Voltage imbalance means one phase is higher or lower than the others. It can come from uneven loading, in which one phase carries far more single-phase equipment than the others, from poor connections that drop voltage on one leg, or from conditions on the utility side. Motors are sensitive to imbalance, and a small difference in voltage can cause a larger difference in current and heat.
The symptoms are subtle. Motors that run hotter than normal, equipment that trips on overload, shortened motor life, lights that dim or brighten when large equipment starts and electronic equipment that resets for no clear reason are all possible. Because the problem builds slowly, owners often blame the equipment instead of the supply.
A technician measures voltage on each phase, under no load and under load, and compares. Measuring current on each phase shows whether load is balanced. When the supply itself is out of tolerance, the utility may need to be involved. The guide on FPL outage versus your electrical problem explains how to tell whether the issue is on the utility side.
Motor symptoms: what they tell you
Motors are good witnesses. A motor that hums but will not start suggests a lost phase or a mechanical jam. A motor that starts slowly, runs hot or trips its overload repeatedly suggests imbalance, low voltage or a worn bearing. A motor that runs backward suggests that two phases have been swapped, which can happen after repairs or utility work and can damage pumps and compressors if not corrected quickly.
Noise and vibration offer more clues. A motor that growls or vibrates more than usual may be suffering from single-phasing or imbalance, while a motor that is quiet but ineffective may have a mechanical problem. Burned smells from a motor, starter or panel should never be ignored. The page on burning smell from outlet explains why a burning odor is always treated seriously, and the same logic applies in a mechanical room.
Whenever possible, record what the equipment is doing: which machine, when it began, what changed beforehand and whether other machines on the same supply are affected. A pattern across several motors points to the supply. A problem with one motor points to that motor, its starter or its wiring.
Common causes a technician checks first
Troubleshooting follows the path of the power, starting where the symptom appears and working back toward the source, or the reverse. Common causes include blown fuses or tripped breaker poles, loose lugs in the disconnect or the panel, corroded or overheated connections, failed contactors in motor starters, damaged cable, failed capacitors or control components and problems on the utility side.
The first checks are usually simple. Is voltage present on all three phases at the main? At the panel? At the disconnect next to the machine? At the motor terminals? Narrowing down the point where a phase vanishes finds the fault quickly. Fuses, in particular, can blow one at a time, and a single blown fuse in a disconnect will cause single-phasing.
Safe testing requires care. Measuring live equipment exposes the technician to serious hazards, and the work should be done by qualified people with the right tools. Property owners should not open disconnects or panels, and should not reset breakers or replace fuses without knowing why they operated. Related repair work on distribution equipment is described in commercial panel and switchgear service.
Utility side problems versus building side problems
A fault may be in the building or upstream of it. The utility owns and maintains the lines, transformers and meter up to the service point. If a phase is missing at the meter, the problem may be on their side, and they must be called. If all three are present at the meter but missing downstream, the problem is on the building side.
Storms, vehicle accidents, failing equipment and blown transformer fuses can cause partial outages that affect only part of a neighborhood or a single building. An FPL transformer serving your property may have lost one phase while neighbors on other transformers are fine. This is one reason a business may be partly dark when the block next door is fine.
A technician can measure at the meter and determine which side holds the fault, then explain what to report to the utility and what repairs belong to the building. The page on utility meter and service responsibilities explains the boundary in more detail. If a power line is down, stay clear and call 911 or the utility; the page on power line down at property explains why.
Protecting motors and equipment from phase problems
Protection against phase problems is inexpensive compared with replacing motors. Phase monitors are small devices that watch the incoming voltage and disconnect equipment if a phase is lost, reversed or badly unbalanced. Many compressors, pumps and elevators already include them. Where they are missing, adding one is a straightforward improvement that protects expensive equipment.
Surge protection also plays a role. Voltage spikes from storms and switching can damage drives, controls and electronics, even if they do not stop the equipment immediately. Whole-building surge devices at the service and local devices at sensitive equipment add layers of protection. The pages on surge protection and whole-home surge protector types explain the difference between types, and why no device removes all risk.
Regular maintenance of connections, fuses, contactors and disconnects reduces failures. Tightening and cleaning, replacing worn contactors and checking the condition of fuses and disconnects catch problems before they stop a machine. A repair log that records which equipment has failed and when helps spot patterns.
Light industrial, warehouse and restaurant examples
In a warehouse, a conveyor motor that hums but will not start while the lights remain on is a classic single-phase symptom. The technician checks the disconnect, finds a blown fuse on one leg and, before replacing it, looks for the reason it blew, such as a jammed motor or a loose connection that overheated. Replacing the fuse alone would risk a repeat.
In a restaurant, a walk-in cooler compressor that cycles on and off and runs hot may suffer from imbalance caused by too many single-phase loads on one leg of the panel. Rebalancing circuits, which means moving some loads to the other phases, can reduce heat and extend equipment life. See restaurant electrical service for more on kitchen loads.
In an office building or medical suite, rooftop air conditioners are the usual three-phase loads. When one trips on phase loss during a hot afternoon, the whole space heats up quickly. The page on warehouse and industrial electrical service covers heavier equipment and typical problems in those buildings.
After repairs, utility work or new equipment: phase rotation
Three-phase power also has a direction, called phase sequence or rotation. If two of the three conductors are swapped, motors run backward. Fans move air the wrong way, scroll compressors may be damaged quickly and pumps may fail to move water. Rotation problems appear after utility repairs, panel work, generator connections and new equipment installations.
A technician checks rotation with a meter designed for the purpose before connecting motors, and corrects it by swapping two conductors at a suitable point. The correction should be made at the source or the disconnect, not at individual motors, so that all equipment on the supply sees the same rotation. Equipment with sensitive compressors usually has protection that refuses to start with reversed rotation.
Whenever work is done on a three-phase supply, it is worth asking that rotation be confirmed before equipment is turned back on. This is a simple check that prevents expensive damage, and it belongs on the closeout list for any panel, service or generator job.
Safe steps while you wait for service
If you suspect a phase problem, switch affected motors and equipment off, so they do not burn out while trying to run. Leave breakers and disconnects as they are, and do not replace fuses unless you know why they blew and are qualified to work on the equipment. Keep people away from any equipment that is hot, humming loudly, smoking or smells of burning.
Gather facts. Note which equipment is affected, when it began, what else was running, whether lights and outlets are normal and whether neighbors have power. If your building has a monitoring panel or alarm for phase loss, note what it shows. Take photographs of nameplates and any displays from a safe distance.
If there is smoke, fire or a strong burning smell, leave the building and call 911 first. If the problem is a partial outage and nothing seems hot or damaged, call for service and describe what you see. Quotes are given only by phone, and complicated jobs need an on-site visit. A service call charge applies and is explained before anyone is dispatched. Call when you are ready, and the next step will be explained.
Questions people ask
What happens when a three-phase motor loses one phase?
A running motor may keep turning but draws much more current on the remaining phases and can overheat quickly, while a stopped motor usually hums and will not start. Turn the equipment off to avoid damage and call. Repeated restart attempts can burn out the motor, so it is best to stop and have the supply checked.
Why do my lights work while my machine will not run?
Lights and outlets often use only one or two phases, so they can keep working when the third phase feeding a motor is missing. This pattern is common in single-phasing. A technician measures voltage on each phase at the panel, disconnect and motor to find where the phase disappears and what caused it.
Is the problem the utility or my building?
Measuring at the meter helps. If a phase is missing at the meter, the fault is likely on the utility side and must be reported to them. If all three phases are present at the meter but missing further downstream, the fault is in the building. A technician can test and tell you which side owns the repair.
Can I just replace a blown fuse myself?
It is not recommended without knowing why the fuse blew. A fuse usually blows for a reason such as a jammed motor, a short or a loose connection, and replacing it may cause the same failure again or cause damage. Work inside disconnects also involves live-electricity hazards that should be left to qualified technicians.
What is voltage imbalance and why does it matter?
Imbalance means the three phases are not delivering equal voltage, often from uneven loading, poor connections or utility conditions. Motors heat up and wear faster under imbalance, and overloads trip more often. A technician measures each phase under load and may rebalance circuits or repair connections to bring things back into line.
How do I get a price to troubleshoot three-phase problems?
Quotes are given only by phone. A description of the symptoms and equipment lets the process start, but troubleshooting complicated systems needs an on-site visit so the cause can be confirmed before work is priced. The service call charge is explained on the phone before anyone is dispatched. Call and describe what is happening.
For "Troubleshooting Three-Phase Power Problems", a phone call comes first. Describe the circuit, the breaker or the equipment, and we will talk through the safe next steps and whether the job needs an on-site look.
Related pages
- Switchgear Service: Service for commercial panels, distribution equipment, breakers and bus problems in larger South Florida electrical rooms, with safe planning of outages.
- Warehouse Service: Electrical service for warehouses and logistics facilities: high-bay lighting, dock equipment, overhead distribution and motor loads, explained plainly.
- Power Loss Troubleshooting: Private South Florida guide for routing complete outages, partial power loss, flickers and property-side electrical problems.
- Commercial Electrical Troubleshooting: Operations-first commercial electrical troubleshooting guidance for managed properties in Broward County and the cities from Boca Raton to North Miami.
- Utility vs Home: How to tell a utility outage from a fault at your own property, with simple safe checks to run before anyone is called and what each result means.
- Apartment Buildings: Electrical repair for apartment buildings in South Florida: meter banks, shared panels, common-area faults and planning repairs around occupied units.
Measurements a technician takes and what each reading suggests
Troubleshooting begins with measurement, not guesswork. With a meter suited to the voltage, the technician reads between each pair of phases and from each phase to ground, at the panel and again at the equipment. Three roughly equal readings suggest a healthy supply. One low or missing reading points toward a loose connection, a blown fuse or an open conductor somewhere upstream of the point being measured, and comparing the two measuring points shows how far upstream to look. Readings are taken with the equipment running and then, where safe, stopped, because comparing the two conditions often reveals whether a problem comes from the supply or from the machine itself.
Current readings tell a different story. A clamp meter on each leg of a running motor shows whether the load is balanced. A motor drawing much more current on one leg than the others may be suffering from voltage imbalance, a worn winding or a poor connection. The technician compares readings with the nameplate and with earlier visits if records exist, which is another reason to keep notes of past service. If a utility problem is suspected, the technician documents the readings and the times, which gives the utility the information it needs to investigate its equipment instead of simply being told that something seems wrong.
These measurements are done carefully and only by trained people, because energized panels are dangerous. Owners should avoid opening equipment themselves. What helps is a note of when symptoms began and what changed around that time, such as new equipment, storm activity or utility work in the area. Call us to talk about what you are seeing, and the scope and any quote are explained before work begins. While waiting for service, leave the equipment off if it is making unusual noises or smells, since running a motor on a damaged supply can turn a repair into a replacement.
Fuses, contactors and loose lugs: the small parts behind large problems
Many three-phase failures trace back to small, ordinary parts. A fuse that has blown on one leg leaves a motor running on two phases. A contactor with a pitted contact passes current on two legs but only weakly on the third. A lug that was never tightened properly heats up over months, discolors and eventually burns through. None of these are dramatic until the day the equipment stops, which is why they are often found only after a failure. Heat is the common enemy here, so thermal imaging or a careful hand-off inspection after the panel is safely opened by a professional can reveal connections that are running hotter than their neighbors.
A technician checks these parts with power off and locked out whenever possible, looking for discoloration, loose terminals and signs of arcing. Tightening connections to the manufacturer's specified torque matters, since over-tightening can damage a lug as surely as leaving it loose. Replacement parts should match the rating of the original, and the technician explains why when a different part is recommended. Contactors and fuses are inexpensive compared with the motors they protect, so replacing worn ones during a scheduled visit is often more sensible than waiting for a failure at a busy time.
Owners can reduce risk by scheduling periodic inspections and thermal checks of important panels, especially in busy kitchens, warehouses and workshops. If equipment has repeatedly tripped or smelled hot, mention it when you call. A pattern of small events often points to the real cause. Call us to describe the situation, and the scope and any quote are explained before work begins. When a repair is finished, ask the technician to note what was replaced and the readings afterward, since that record makes it easier to spot the same issue returning in the future.
