Why this pattern is different from a single tripped breaker
Most electrical failures in a home affect one circuit: a room, a bathroom or a kitchen counter. When half the house loses power, the failure is usually upstream of the individual circuits, at the main breaker, the panel connections, the service wires or the utility supply. That is why this pattern is taken seriously.
The way a typical American home receives power explains why. Utility service comes in as two hot conductors, each carrying 120 volts relative to a shared neutral, and 240 volts between them. The panel divides circuits between the two halves, often called legs or phases. Lights and general outlets use one leg and the neutral at 120 volts. Large appliances such as air conditioners, dryers and ranges use both legs at 240 volts.
If one leg is lost, every circuit fed by that leg goes dead, while circuits on the other leg keep working. Half the house loses power. Appliances that need both legs may not work at all, or may run poorly. This is a different failure than a tripped breaker, and the fixes are different too.

The pattern can be confusing because the dead and live areas may not match room boundaries. Circuits in the same room can be on different legs, so a single room can have some outlets working and some not.
The lost leg: when one of the two hot lines goes away
A lost leg, sometimes called a lost phase in residential contexts, occurs when one of the two hot conductors stops delivering power. Causes include a failed connection at the meter or the service entrance, a damaged service conductor, a failed main breaker pole, a blown utility fuse or a problem on the utility's side of the system, such as a failed transformer connection or a downed line.
Symptoms include half of the lights and outlets dead, 240-volt appliances not working or running weakly, and sometimes a hum from the air conditioner if it tries to run on one leg. Electronics on the working leg continue to operate normally, which can mislead people into thinking the house is fine.
Distinguishing a utility cause from a house cause is the first step. Check whether neighbors have problems and look outside. If the utility's overhead lines are damaged or a neighbor's power is also out, the utility must respond. The guide on telling a utility outage from your own electrical problem helps. If neighbors are fine and the problem is within your equipment, a technician is needed.
If you can see damage to the service mast, the meter or the wires at your house, stay away and call. See service mast and weatherhead repair and meter box damaged or hanging.
The loose or lost neutral: dim lights on one side and bright on the other
The neutral conductor is the shared return path that keeps voltage balanced between the two legs. When it is loose, corroded or broken, the balance is lost. Instead of both halves of the house getting 120 volts, one half may get much less and the other much more, with the total still equal to 240 volts. That can show up as lights that are dim in some rooms and unusually bright in others.
This is dangerous. Equipment on the high side can receive well over its rated voltage. Electronics, appliances, light bulbs and power supplies can be damaged or destroyed, sometimes within seconds. Bulbs that burn out suddenly or flash brightly, appliances that run hot or smell, and electronics that fail are signs. A loose neutral can also produce heat and arcing at the failed connection.
Causes include a loose connection at the panel's neutral bar, at the meter or at the service entrance, corrosion, damaged service conductors and utility-side problems. Wind, vibration, water intrusion and age can all contribute. Salt air accelerates corrosion near the coast. The guide on salt air corrosion explains why waterfront homes are more exposed.
If you see lights that are noticeably bright in some rooms and dim in others, treat it as urgent. Turn off sensitive electronics and large appliances, and consider turning off the main breaker if it can be reached safely, then call right away. See why lights flicker for related patterns.
Main breaker and panel causes
Not all half-house outages come from outside. The main breaker in the panel is a two-pole device that connects both legs. One pole can fail or trip independently, cutting one leg. Failed contacts, worn mechanisms and heat damage can all cause this.
Connections inside the panel can also fail. A loose or burnt connection where one of the service conductors attaches to the main breaker or lugs can cut off a leg. Heat damage at that point may be visible as discolored or melted insulation, or may be hidden. A burning smell near the panel suggests this. See burning smell from an outlet or panel.
A panel with a failed bus bar section or a damaged connection can lose power to a group of breakers on one side. In older panels, particularly those with known issues, this is a more common failure. See Federal Pacific panels and Zinsco and older panel brands.
These are not do-it-yourself checks. Opening the panel exposes live service conductors, and the main breaker does not de-energize them. A technician works with the proper tools and procedures, and often coordinates with the utility to cut service if the work requires it.
What you can safely check
There are a few things you can do safely. First, look at the panel's main breaker, without opening anything. Is it in the on position, or has it tripped to the middle? A fully tripped main breaker affects the whole house, not half, but a partial trip could be confusing.
Second, check whether neighbors have power and look for visible utility problems from a safe distance. Do not approach downed lines. See power line down at your property. Third, note which parts of the house are dead and which are working, and which large appliances are affected. Write down which lights are dim or bright.
Fourth, protect equipment. If any lights are bright or dim, or you suspect a neutral problem, unplug sensitive electronics such as computers, televisions and chargers, and turn off large appliances. If it is safe, turn off the main breaker to remove all power until help arrives. Only operate the main breaker if the panel is dry, undamaged and does not smell of burning.
Do not try to fix the problem by resetting every breaker repeatedly, do not remove the panel cover and do not touch the meter or service conductors. Treat the electrical service as energized and dangerous at all times.
- Look at the main breaker position without opening the panel
- Check whether neighbors have power and look for utility damage from a distance
- Note which areas are dead, dim or bright
- Unplug sensitive electronics and shut off large appliances
- Turn off the main breaker only if the panel is dry, undamaged and safe to reach
- Do not open the panel, meter or service equipment
Why large appliances behave strangely
Appliances that use 240 volts, such as air conditioners, electric ranges, dryers and water heaters, need both legs. If one leg is lost, they may not operate at all. A dryer may tumble but not heat. A range may have burners that do not work. An air conditioner may hum but not start. A water heater may not heat.
Compressor motors, as in air conditioners and heat pumps, can be damaged by running on reduced or incorrect voltage. If you notice an air conditioner humming and not starting, turn it off at the thermostat and the breaker, and leave it off until a technician has found the cause. Running it repeatedly can burn out the compressor.
Electronics and appliances on 120 volts can also be at risk if a neutral problem is present. Refrigerators, which contain compressors, and sensitive electronics should be protected. If you suspect a neutral issue, unplug what you can.
After the problem is fixed, check appliances. Some may need to be reset or inspected. A technician may suggest surge protection to reduce the damage from future events. See surge protection.
Who fixes what: utility side versus your side
Responsibility is divided at a specific point. In general, the utility owns and maintains the lines, the transformer and the meter. The property owner owns and maintains the service entrance equipment on the house side, including the service mast, weatherhead, service conductors from the weatherhead to the meter in many cases, the meter socket and everything beyond. The details vary by utility and by whether service is overhead or underground.
The guide on utility meter and service responsibilities explains where the line falls. If the cause is on the utility side, the utility must make the repair. If the cause is on your side, a technician repairs it, and the utility may need to disconnect and reconnect power around the work.
Sometimes the cause is not obvious. A technician with the right instruments can measure voltage at the meter and at the panel, and determine whether the supply arriving is correct. That distinction saves time and avoids unnecessary repair. If the supply is wrong, the utility is called with specific information. If the supply is right and the house is wrong, the repair is in the house.
After a storm, the situation may involve both. Wind can damage a service mast or weatherhead, which the owner must fix, and the utility reconnects after inspection or permitting is complete. See after hurricane electrical safety.
Typical scenes in South Florida homes
A ranch house in Broward County with an older panel loses half its lights on a hot afternoon when the air conditioner starts. The panel's main breaker feels warm, and there is a faint burning smell. A technician finds a burnt connection at one of the main lugs and a damaged main breaker, likely the result of loosening over decades of heating and cooling.
A waterfront home in Sunny Isles Beach notices lights dimming in the kitchen and brightening in the bedrooms after a windy night. The neutral connection in the service mast has corroded from salt air and loosened in the wind. Replacement of the damaged service conductors and connections restores balance, and a surge protective device is added.
A townhouse in Coral Springs loses power to half of the rooms after a heavy storm. Neighbors are fine. Water entered the meter socket and burned a terminal. Replacing the meter socket, with coordination with the utility, restores power. The house also needs its air conditioner checked for damage.
These are examples, not predictions. Each case is different, and the cause is found by testing rather than guessing.
What a technician does and checks
The technician starts with a conversation about what happened, when and what was noticed. Then comes testing. Voltage is measured at the meter, at the main breaker, at the bus bar and at selected circuits. These measurements show where the supply is correct and where it fails.
If voltage at the meter is wrong, the issue is likely on the utility side or at the meter socket, and the utility may need to be involved. If voltage is correct at the meter but wrong inside the panel, the technician traces the service conductors, main breaker and connections. If voltage is correct at the panel but certain breakers are dead, the problem lies in those breakers or in the bus bar.
Repairs may include tightening or replacing a connection, replacing a main breaker, replacing a meter socket, replacing service conductors or repairing a service mast. Some repairs require the utility to disconnect power and reconnect it afterward, and permits may be needed for service-level work.
After repairs, voltages are re-measured to confirm that both legs and the neutral are correct, and that equipment is receiving the right supply. The technician may suggest surge protection and a review of appliances that may have been affected. Quotes are given only by phone, and larger or complicated jobs need an on-site visit. A service call charge applies and is explained on the phone before dispatch.
Protecting yourself and your equipment while you wait
While waiting for a technician, protect people first. Keep children and pets away from the panel and the meter. Do not use extension cords from working outlets to power things in dead areas, as this can overload the working leg. Avoid running large appliances.
Protect equipment next. Unplug computers, televisions, game consoles and chargers, especially if you saw dim or bright lights. Turn off the air conditioner and other motor loads at the thermostat or breaker. Keep refrigerators and freezers closed to preserve food, and consider moving essential medical equipment to a safe backup supply if you have one.
Document what happened. Take notes and photographs of the lights, the panel exterior and the meter from a safe distance. Note what damage you find in appliances. This helps the technician and may help with an insurance claim.
If there is any smoke, sparks, burning smell or visible damage, leave the area and call 911. For more on how to decide how quickly to act, see emergency or can it wait.
When to call and what to have ready
Call right away when half the house has no power, particularly if any lights are dim or bright, if there is a burning smell or hum at the panel, if an air conditioner is humming but not starting or if you suspect storm damage. Call the utility as well if neighbors are affected or if lines are down.
Have ready: which areas have power and which do not, whether any lights are dim or bright, which large appliances are affected, when it started and what happened before, such as a storm or a loud noise. Note whether neighbors have power. If safe, note the position of the main breaker.
Call and describe what you see. The person on the phone will ask a few questions, explain how quotes and the service call charge work and tell you what to expect from the visit. A half-dark house is a clear signal, and a technician can read it quickly.
Questions people ask
Why do some of my lights work and others do not?
Homes receive power on two legs. If one leg is lost because of a failed connection, a main breaker pole, a service conductor or a utility problem, every circuit fed by that leg goes dead while the other leg keeps working. The pattern does not follow rooms, since circuits in one room can be on different legs.
Why are some lights bright and others dim?
That pattern often points to a loose or damaged neutral conductor, which lets voltage swing between the two halves of the house. Equipment on the high side can be damaged quickly. Turn off sensitive electronics and large appliances, and call right away.
Is it safe to keep using the parts of the house that have power?
It is risky if you see bright or dim lights, smell burning or hear humming. Use as little as possible, unplug electronics and avoid large appliances until a technician has checked the service. If everything on the working side looks normal, limit use anyway and call promptly.
Why will my air conditioner not start?
Air conditioners need both legs. If one leg is lost, the compressor may hum without starting. Turn the unit off at the thermostat and breaker to avoid damaging the compressor, and leave it off until the power problem has been fixed and checked.
Is this the power company's problem or mine?
It can be either. If neighbors also have problems or utility lines are damaged, the utility must respond. If neighbors are fine, the cause may be in your meter socket, service conductors, main breaker or panel. A technician can test voltage to tell which side holds the problem.
How are quotes provided for service problems like this?
Quotes are given only by phone. Simple repairs may be quoted after a few questions, while service-level or complicated jobs need an on-site visit. A service call charge applies and is explained on the phone before dispatch.
Dealing with "When Half the House Has No Power"? Tell us where in the building it happens and what changed before it started. We will say what the electrician would check and how the visit charge is explained.
Related pages
- One Room Dead: When one room loses power and the rest of the house is fine, the cause is usually a breaker, a hidden GFCI or a failed connection. Here is how to trace it.
- My Home Only Out: When only your property is without power, the cause may be the main breaker, meter, service drop or a utility fault. Learn what to check and who handles it.
- Power Loss Troubleshooting: Private South Florida guide for routing complete outages, partial power loss, flickers and property-side electrical problems.
- Meter Socket: Who does what when a meter socket is damaged: the owner, the electrician and the utility, how power is disconnected and restored, and how to plan the repair.
- Utility vs Home: How to tell a utility outage from a fault at your own property, with simple safe checks to run before anyone is called and what each result means.
- Bulbs Burning Out: Bulbs that keep burning out usually point to heat, voltage, loose sockets or a mismatched dimmer. Learn the causes and what to check before replacing again.
