How lightning gets into a building's electrical system
A lightning strike does not have to hit the house to affect it. A direct strike on the roof, a mast or a tree beside the house is the most severe case, but strikes on a nearby pole, a transformer, a neighbor's property or the ground can send surges along utility lines, through the soil and into the building. Surges can enter through the power service, through cable and phone lines, through the grounding system, and through metal plumbing, fencing or conduit.
The energy moves in very short pulses that can be many times the normal voltage. Even a brief pulse can punch through insulation, burn contacts and damage the electronic components inside appliances. The path the energy takes is not predictable. It will try to reach the ground by any route it can find, and sometimes that route is through household wiring.
Lightning can also cause a fire directly, by heating wiring or igniting materials near the point where it enters. Fires from a strike may not start immediately. Smoldering inside a wall or an attic can appear hours later. If you smell burning, see smoke or hear crackling after a nearby strike, leave the building and call 911.

Why a house can look fine and still be damaged
Some of the most common aftermath is quiet. The lights come on, the television works, the breakers have not tripped. It is tempting to conclude that nothing happened. But surge energy tends to damage components gradually, by weakening insulation, pitting contacts and stressing electronic parts. A device that survived the strike may fail weeks or months later, and a circuit whose insulation was compromised may eventually fault.
Hidden damage often turns up in places owners do not look. A surge may weaken the connections inside a panel, so a breaker begins to run warm or fails to trip under overload. It may degrade outlets so they become loose or intermittent. It can damage the control boards in air conditioners, pool equipment, garage door openers and smart devices. Low-voltage systems such as doorbells, thermostats, alarms and network equipment are often hit because they connect to long runs of wire that act like antennas.
A professional check cannot promise to find every problem, but it can find many of them early and address the ones that matter for safety.
Signs to look for after a nearby strike
Walk through the property and note what you see, hear and smell. Some signs are immediate and obvious, while others emerge during the next few days. Write them down and take photographs, because they help the electrician and your insurer.
- A burning smell, smoke, scorch marks or discolored cover plates at outlets or switches
- Outlets, switches or lights that no longer work, though breakers look normal
- A breaker that trips repeatedly or will not reset
- A buzzing, crackling or humming sound from the panel
- Appliances, thermostats, the router or the garage door opener that stopped working
- Flickering or dimming lights that were not a problem before
- Damaged or split bark on a nearby tree, a cracked chimney or scarred masonry
- A pool pump, sprinkler controller or outdoor light that no longer operates
What is safe to do right away
If there is any sign of fire, get everyone out and call 911. If a person was struck or is near someone who was, call 911 and give first aid if you are trained, since a person struck by lightning does not carry a charge.
If there are no signs of fire, the safest approach is to stop using the affected circuits and avoid stressing the system. Do not keep resetting a breaker that trips. Do not keep plugging in things to see if they work. Do not open the panel cover or touch burnt devices. Turn off and unplug sensitive electronics that were exposed, and leave a lamp on a circuit you believe is working, so you notice if power changes.
If the main breaker has tripped or the home has lost power, remember that a utility outage may also be involved. Check whether neighbors have power. Our guide to telling a utility outage from your own electrical problem explains how. If the neighbors have power and you do not, the problem is likely on your side of the meter.
What an electrician checks
The assessment is systematic. A technician starts at the service, because that is where much of a surge enters, and then moves through the panel, the branch circuits and the grounding. They also ask what happened: where the strike was, when it occurred and what changed afterward. That history points the inspection toward likely damage.
Using testing instruments rather than only the eye, a technician looks for conditions that would not be visible. They measure voltage at the service and at the panel, check that breakers operate and hold, check the integrity of the grounding system and look for signs of heat inside the panel. They test circuits that were affected and look at the surge protection, if any, to see whether it has done its job.
- Service entrance: meter socket, mast, weatherhead and service conductors for pitting, burns or loose terminations.
- Panel: bus bars, breakers and connections for heat marks, pitting and soot.
- Grounding and bonding: ground rods, the connection to the water pipe where present, and the bonding of metal systems.
- Branch circuits: outlets, switches and fixtures that stopped working or show heat.
- Surge protective devices: whether they show a failure indicator or need replacement.
- Low-voltage and communication lines, which often carry surges into equipment.
- Outdoor equipment such as pool pumps, landscape lighting and sprinkler controllers.
Surge protection and what it can and cannot do
A whole-home surge protective device, installed at the panel, is designed to limit the voltage reaching the building's wiring and equipment during a surge. A direct hit can overwhelm any protective device, and no product can promise complete protection from a strike on the building itself. But protection at the panel, combined with point-of-use protectors on sensitive devices, reduces the stress on everything downstream.
After a strike, a protective device that did its job may be spent. Many units have an indicator light or a display that shows whether the protection is still active. If the indicator is dark or shows a fault, the unit should be replaced. If a house had no protection and a strike occurred, installing it is a reasonable step. Our pages on surge protection, whole-home surge protector types and whole-home versus point-of-use surge protection explain how the options differ.
Surge protection works best with good grounding. A protective device sends surge energy to ground, and if the grounding system is poor or damaged, the energy has no easy path. That is one reason an inspection after a strike covers the grounding and bonding.
Grounding and bonding after a strike
The grounding system is the part of the installation that gives lightning and fault current a safe route into the earth. After a strike, the connections to ground rods, water piping and the service equipment may be pitted, loosened or burned. Soil conditions in much of South Florida, including sandy and sometimes saline ground near the coast, affect how well a rod performs, and corrosion over time can degrade the connections.
Bonding is the related practice of connecting metal parts so that they stay at the same electrical potential. Metal pipes, a pool's metal parts, the cable system and the panel enclosure are typically bonded together. A strike can damage those connections, and a break in the bonding can leave metal parts at different voltages, creating a shock hazard. A technician will inspect the visible bonds and may test them.
Our guide on grounding and bonding explained covers the principles in plain terms. If a strike hit near your pool, a bonding check is especially worthwhile, and our page on pool and spa electrical wiring describes the requirements for those areas.
Appliances, air conditioners and electronics
Appliances with electronic control boards are the usual casualties. Air conditioners and heat pumps are particularly exposed because they have long outdoor runs, large motors and control boards. If your system stopped cooling after a strike, the cause may be a failed control board, a damaged capacitor or a damaged contactor, and a heating and cooling technician is the right person for the equipment. The electrician checks the circuit feeding it and the disconnect.
Do not repeatedly try to restart an air conditioner that stopped after a storm. If the cause is an electrical fault, each attempt can add damage. Turn the breaker off and have the circuit and equipment checked. Our page on AC condenser electrical connections explains how the supply side of the equipment is built.
For computers, televisions and other electronics, ask the manufacturer or a repair shop whether they can be tested. Insurers often ask for a record of what was affected, so keep a list with the make, model and what failed.
Insurance, documentation and photographs
Lightning damage is a typical homeowners insurance claim, and many carriers handle it as part of a standard policy, though terms differ and only your carrier can say what is covered. Report the loss promptly. Take photographs of visible damage, note the date and time of the storm, and keep a list of devices that stopped working. If a neighbor reported a strike, a nearby tree, a transformer or a pole may be part of the story.
Ask the electrician for a written summary of what was found. A written record that the panel, wiring and grounding were checked after the strike supports your claim and later helps if you sell the property, since inspectors may ask about prior events. Our guide to insurance inspection electrical findings and the page on electrical inspections when buying a home explain how that history comes up.
Do not discard failed components until the adjuster has seen them or approved disposal. Evidence of the damage may matter to the claim.
Preparing for the next storm season
Lightning is a fact of life during the wet season, so planning pays off. Have the panel and the grounding inspected, install surge protection at the panel, and consider protectors for sensitive electronics, the air conditioner and pool equipment. Unplug sensitive devices during severe storms if you can do so safely and you are not near the equipment during a storm. Label the panel so that you can quickly turn off the right circuits if something goes wrong. Our guide on your electrical checklist before hurricane season covers similar preparations.
Do not attempt to install lightning protection or surge devices yourself. Work at the panel exposes you to live conductors, and lightning protection systems are specialist work. For a house with a metal roof, a tall mast, or a detached structure such as a dock or outbuilding, ask the electrician about those specific situations, since each has different considerations.
When you call, tell us what happened, where the strike seemed to be and what has stopped working. Quotes are given only by phone, and because hidden damage cannot be priced sight unseen, the work usually involves an on-site visit with a service call charge that is explained on the phone before dispatch. If you suspect a hazard now, such as a hot smell or a panel that hums, keep clear and call.
Questions people ask
My house seems fine after the storm. Do I still need a check?
If the strike was on or near the property, a check is sensible. Surges can weaken insulation, connections and electronics without any immediate sign, and the failures can appear weeks later. A technician can test the panel, grounding and affected circuits and look for heat damage. If nothing nearby was struck and everything works normally, it is less pressing.
Is it safe to reset a breaker that tripped during the storm?
You can try one reset if there is no burning smell, smoke or visible damage, but do not keep resetting. A breaker that trips again, or a panel that hums or smells hot, means a fault. Leave it off and call. If you see smoke, sparks or smell burning anywhere, leave the building and call 911.
Will a surge protector prevent lightning damage?
It reduces the risk but cannot promise protection, especially from a direct hit on the building. A whole-home device at the panel limits surges coming through the service, and plug-in protectors help sensitive electronics. Good grounding is essential. After a strike, check whether the protector's indicator shows it is still working, since a spent unit needs replacement.
My air conditioner stopped working after a storm. Who should I call?
Turn the breaker off and avoid repeated restarts. An electrician can check the circuit, the disconnect and the supply to the unit for lightning damage, while a heating and cooling technician handles the equipment itself, such as control boards and capacitors. If you are unsure which is needed, describe the symptoms when you call.
How much will it cost to check for lightning damage?
Quotes are given only by phone. A check after a strike usually needs an on-site visit, because hidden damage cannot be priced from a description. There is a service call charge for that visit, and it is explained on the phone before any technician is dispatched. Any repairs found are quoted by phone after the findings.
Does insurance cover lightning damage?
Many homeowners policies cover it, but terms vary, and only your carrier or agent can confirm what yours includes. Report the loss promptly, photograph visible damage, list the items that failed, and ask the electrician for a written summary of findings. Keep failed parts until the adjuster approves disposal, since they can serve as evidence.
If "Electrical Damage After a Lightning Strike" sounds like your problem, call and describe what you see, hear or smell at the panel, the outlet or the fixture. We explain what the work involves, and some jobs need a visit before a quote.
Related pages
- Whole-Home & Commercial: A practical guide to layered residential and commercial surge protection in Broward County and the cities from Boca Raton to North Miami.
- Surge Protector Types: Panel-mounted surge protective devices compared: Type 1 and Type 2 designs, ratings that matter, and what to expect from an installation in Florida.
- Grounding and Bonding: What grounding electrodes, bonding jumpers and equipment grounds each do, why many older Florida homes lack them, and how a technician checks yours.
- Post-Storm Flicker: Lights flickering after a storm may be utility restoration or damaged service equipment on your side of the meter. Learn how to tell them apart and what to do.
- Hurricane Checklist: A pre-season electrical checklist for South Florida homes: panels, outdoor equipment, generators and surge protection to review before the first storm.
- Buzzing Lights: A buzzing or humming light fixture can come from a ballast, LED driver, dimmer or loose wiring. Learn which sounds are only annoying and which need attention.
The days after a strike: a calm order of steps
Once everyone is safe and the storm has passed, resist the urge to switch everything back on at once. Walk through the home and write down what you notice before touching anything: which lights, outlets and appliances are dead, which behave oddly, and whether any smell or marks are present. Keep a simple list with room names. This record helps the technician and also helps if you later discuss the event with an insurer, since memory fades quickly after a stressful night. Even a few lines per room are enough, as long as they are written down soon while the details are still fresh.
Keep electronics and appliances unplugged or switched off until someone has checked the supply. Equipment that was damaged but still limps along can fail harder when power returns, and a damaged neutral or ground can send the wrong voltage to devices. Do not reset the main breaker repeatedly or try to test outlets with improvised tools. If the meter, mast or service wires look damaged or are on the ground, keep away and tell the utility. Patience here is genuinely protective, since a few more hours without power costs far less than replacing equipment that was switched on too soon.
When you call, describe what was on at the time of the strike, what you saw and heard, and what has been found dead since. Mention whether neighbors were affected, as that helps separate a problem at your home from a wider outage. The technician can then plan which parts of the system to examine first. Call us to confirm availability, and the scope of any work will be explained before it begins. The more complete your description, the better the technician can plan, and the less time is spent rediscovering things you have already noticed yourself.
